Наклейки на авто брембо
Brembo graphic легковые и грузовые автомобили наклейки и виниловые
Side Refine Panel
Посмотреть по категориям
Марка
Состояние
Введите действительный ценовой диапазон
Формат покупки
Находится
Параметры доставки
Показать только
Посмотреть по параметру Color
Посмотреть по параметру Brand
Brembo
Один магазин для покупки всех товаров вашего любимого бренда
Brembo Car & Truck Graphics Decals
Brembo is the international leader in design, development, and production of vehicle brake systems. Since its inception in 1961, the Bergamo, Italy-based company has supplied industry standard products to high-performance automobile and motorcycle owners worldwide. Major car and truck manufacturers that they have partnered with include Mercedez-Benz, BMW, Nissan, and Ferrari.
What are Brembos decals made of?
All decals are made with a base of high-temperature vinyl, which is a material that can withstand the hotter temperatures a car can be without actually being on fire. On top of the core, a design is printed onto a film. On the bottom, an adhesive, typically a glue, is applied. Afterwards, paper with one side coated in silicone covers the adhesive so that it can be opened for later use.
How can these decals be neatly applied?
To keep a good foundation for this action, cleanliness is the key. The rear window or another surface must be clean and completely free of debris or dust. The surface, as well as the sticker, must be ready for adhesion. Rub out any air bubbles between the decal and the protective paper. Carefully peel off the back paper. If it ever gets caught, place the paper back on and try again. Slowly and cautiously lower the unpeeled Brembo logo onto the caliper or another surface. Choose a location with a flat surface to make sure that there are no air bubbles.
What does the standard eight-pack consist of?
The standard eight-pack, listed as «Brembo High-Temperature Brake Caliper Vinyl Decal Sticker Set of Eight (any Color),» consists of eight newly printed Brembo decals. The black lettered accessory comes in two sizes, four of each. The ones for the front caliper is 3 inches wide, while the back ones are 4 inches. Each decals design is the official Brembo logo and emblem.
What does the curved eight-pack consist of?
The curved eight-pack, also known as «Brake Caliper Brembo X 8 Sticker Decal Curved Straight Graphics Emblem Logo,» is similar to the standard pack of the same amount except with a curved design. By default, they come in black and in three different curvatures. One has no curve, the others have a 10% or 20% curve.
What does the Camaro six-pack consist of?
The Camaro six-pack, sold as «Camaro-Brembo high-temperature brake caliper Vinyl Decal Adhesive 6x (any Color),» is a series of high-temperature vinyl decals sponsored by automobile company of the same name. Like the standard eight-pack, it comes with 3-inch front decals and 4-inch back decals. A major aesthetic difference is that the design on these is black and red, as opposed to the typical plain black.
Наклейки BREMBO на суппорта
После установки новых суппортов и нескольких месяцев эксплуатации всё-таки решил нанести на них логотипы Brembo, так как без них суппорта смотрелись несколько незаконченно=)
Сначала попытался сделать трафарет и нанести логотип краской с баллончика, но ничего хорошего с этого не получилось — краска с баллончика просто не хотела прилипать к суперглянцевой поверхности краски суппорта и при снятии трафарета снималась вместе с ним=)
Намаевшись с таким способом решил сделать всё достаточно просто — заказал логотипы Brembo необходимого размера из обычного оракала белого цвета, предварительно проведя испытания по термостойкости данного материала наклеив полоску на крышку клапанов на моторе и отъездив с ней месяц. В итоге полоска оракала никак не пострадала и чувствовала себя вполне прилично=) ). Если принимать во внимание размеры и мощность моих тормозных механизмов. можно было надеяться. что с оракалом ничего страшного в процессе эксплуатации не произойдёт. Сам процесс наклейки был достаточно простым — помыл суппорта. обезжирил и, собственно, наклеил 🙂 На мой взгляд ничего так получилось.
Для уверенности в жизнеспособности идеи пытался нагреть тормоза на гонках. вроде даже нагрел, но логотипы выжили и своим видом никак не выразили недовольства и по сей день радуют глаз=)